WARNING
TO PREVENT FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
THIS APPLIANCE SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING WATER AND
THAT NO OBJECT FILLED WITH LIQUIDS SUCH AS VASES SHALL BE PLACED ON
APPARATUS.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
iPhone/iPod FM Radio Receiver with CD
Player & Alarm Clock
Warning: To reduce the rise of
The exclamation point within
The lightning flash with
arrowhead symbol, within an
electric shock, do not remove
an equilateral triangle is
intended to alert the user to
the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
cover
(or
back)
no
equilateral
triangle,
is
user-serviceable parts inside.
Refer servicing to qualified service
personnel.
intended to alert the user to
the presence of uninsulated
“dangerous voltage” within
the products enclosure that
Model : PICL48
may
be
of
sufficient
magnitude to constitute a risk
of electric shock to persons.
IMPORTANT SAFETY INSTRUCTIONS
1)
2)
3)
4)
5)
6)
7)
8)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9)
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
Note: Please read and follow these instructions before using your unit.
- 1 -
CONNECTING THE UNIT TO POWER
LOCATION OF CONTROLS
Plug one end of the AC/DC adaptor into the DC-In jack, and then plug the other end into AC wall outlet.
Before switching on the unit, make sure that the voltage of your electricity supply is the same as that
indicated on the rating plate.
Backu-up Battery
Open the battery door located at the bottom of the unit, insert 2 pcs. ‘AAA’ size (UM-4) batteries with
battery polarities same as shown inside the battery compartment.
In case of AC power outage or interrupted AC power, the current time, alarm time settings and the
stored radio stations are preserved in the memory of the unit.
Important: When the unit is not use for 3 days or more and also the unit is not connect to AC power
during that time, please remove the battery to avoid damage to the set from leakage of battery.
SETTING THE TIME
Before starting to set the time, make sure that the unit is in POWER OFF Mode .
If you have iPod (Except iPod Shuffle) or iPhone
1.) Dock in the iPod/iPhone on the 30 pins Connector
2.) Press the ‘PLAY/PAUSE/SYNC’ button for a few seconds until the display will show SYNC with
flashing, then the unit will synchronize the time same as the iPod/iPhone’s automatically.
If you do not have any iPod/iPhone units
1.) Press and hold the ‘FUNC/CL ADJ’ button for a few seconds, the hour digit in the display will start
flashing.
2.) Press the ‘TUNE+/SKIP+’ or ‘TUNE-/SKIP-‘ button to adjust the hour.
3.) When the correct hour is selected, press the ‘FUNC/CL.ADJ’ button again to enter the minute mode
with minute digit flashing.
4.) Press the ‘TUNE+/SKIP+’ or ‘TUNE-/SKIP-‘ button to adjust the minute.
5.) When the correct time is selected, press the ‘FUNC/CL ADJ’ button to store the time in the memory.
SETTING THE ALARM TIME
Before starting to set the alarm time, make sure that the unit is in POWER OFF mode.
1.) Press the ‘MEM+/AL1’ or ‘MEM/AL2’ button once (You can also use the ‘AL1’ or ‘AL2’ button on the
remote control) and the AL1 or AL2 icon will appear in the display.
2.) Press the ‘FUNC/CL. ADJ.’ button to select the alarm wake up source. You can choose buzzer,
iPod/iPhone, Radio or CD.
3.) Press and hold the ‘MEM+/AL1’ or ‘MEM/AL2’ button for a few seconds, the alarm hour digit will
begin flashing.
4.) Press the ‘TUNE+/SKIP+’ or ‘TUNE-/SKIP-‘ button to adjust the alarm hour.
5.) When the desired alarm hour is selected, press the ‘MEM+/AL1’ or ‘MEM/AL2’ button again, the
alarm minute digit will begin flashing.
1
2
Adjustable Dock Dial
iPod/iPhone Connector
Speaker
11
12
13
14
15
16
17
18
19
Program/Memory/Alarm2 Button
Volume + Button
Volume - Button
Open CD Door Button
Remote Sensor
Display
3
4
CD Compartment
5
Power/Alarm Off Button
Function/Clock Adjust Button
Play/Pause/Sync Button
Skip-/Tune- Button
6
6.) Press the ‘TUNE+/SKIP+’ or ‘TUNE-/SKIP-‘ button to adjust the alarm minute.
7.) When the desired alarm time is selected, press the ‘MEM+/AL1’ or ‘MEM/AL2’ button again to
confirm.
7
DC In Jack
8
FM Antenna
9
Skip+/Tune+ Button
Stop/Memory+/Alarm1 Button
Aux-In Jack
10
Note : If you choose iPod/iPhone or CD as the alarm wake up source, please make sure that you
havehave the iPod/iPhone or CD in place.
- 5 -
- 4 -
TURN OFF THE ALARM
CD OPERATION
1. Press the ‘POWER/AL OFF’ button to turn on the unit.
2. Press the ‘FUNC/CL.ADJ’ button to select the CD mode.
3. Insert a CD disc in the CD compartment and close the CD door, the unit will start reading the disc, it
will play the first track of the entire disc after reading.
4. Press ‘VOL+’ or ‘VOL-‘ button to adjust the volume to the desired listening level.
5. During playing, press the ‘PLAY/PAUSE/SYNC’ button to temporarily pause playing. To resume,
press the ‘PLAY/PAUSE/SYNC’ button again.
When the alarm activate, press the ‘POWER/AL.OFF’ button to turn off the alarm.
SNOOZE FUNCTION
1. Whenever the alarm activate, it can be temporarily suspended for a short period of 10
minutes by pressing the ‘SLEEP/SNOOZE’ button on the remote control.
2. The alarm will then automatically activate again after the 10 minutes SNOOZE period has
ended.
6. To stop playing, press the ‘STOP/MEM+/AL1’ button on the unit or the ‘STOP’ button on the remote
control.
3. This procedure can be repeated for up to approximately one hour.
RADIO OPERATION
Skip Mode
1. Press the ‘POWER/AL OFF’ button to turn on the unit.
1. During play or pause mode, press the ‘SKIP+/TUNE+’ button to go to the next track.
2. During play, press the ‘SKIP-/TUNE-‘ button once to go back to the beginning of the track. Press the
‘SKIP-/TUNE-‘ button twice to go back to the previous track.
2. Press the ‘FUNC/CL.ADJ’ button to select the FM RADIO mode.
3. Press and hold the ‘TUNE+/SKIP+’ or ‘TUNE-/SKIP-‘ button for approx. 1 second, it will start
to search the next radio station in the direction of the search. The search operation simply
finds stations with strong signals. Stations with weak signal can only be tuned in manually.
4. Press the ‘P-MODE/MONO’ button on the remote control to select stereo or mono
broadcasting.
3. In pause mode, press the ‘SKIP-/TUNE-‘ button to go back to the previous track.
Search Mode
1. Press and hold the ‘SKIP+/TUNE+’ or ‘SKIP-/TUNE-‘ button to quickly advance or reverse through
the track at high speed.
2. Release the button to return to normal play.
5. Press ‘VOL+’ or ‘VOL-‘ button to adjust the volume to the desired listening level.
Different Play Mode
SAVING RADIO STATIONS IN THE MEMORY
Press the ‘P-MODE/MONO’ button on the remote control to select different kinds of play mode with the
following sequence.
1. Tune to the desired stations.
2. Press the ‘PROG/MEM/AL2’ button on the unit or the ‘MEM’ button on the remote control, the
display will show the next memory station number flashing.
3. Press the ‘TUNE+/SKIP+’ or ‘TUNE-/SKIP-‘ button on the unit or the ‘M+’ or ‘M-‘ button on the
remote control to select memory number, then press ‘PROG/MEM/AL2’ button to store the
station into the memory.
Repeat Repeat All Random Normal
REPEAT - the track being played and will repeat continuously.
REPEAT ALL - the whole disc will repeat continuously.
4. Repeat step 1 to 3 to store more radio stations in the memory.
5. Up to maximum 20 radio stations can be stored in the memory.
RANDOM – the tracks in the disc will be played in random sequence.
Programming
The programming should be done in STOP mode
1. Press the ‘PROG/MEM/AL2‘ on the unit or ‘PROG’ button on the remote control, LCD display will
show ‘ 1 : - - ‘ with ‘ - - ‘ flash continuously.
2. Use the “SKIP+/TUNE+” or “SKIP-/TUNE-“ button to select the desired track.
3. Press the “PROG/MEM/AL2‘ on the unit or ‘PROG’ button on the remote control again to store the
selected track in the memory, the LCD display will show ‘ 2 : - - ‘ and flash continuously.
4. Repeat steps 2 to 3 to store more tracks in the memory. You can store up to 20 tracks in the
memory.
TO SELECT A STORED RADIO STATION IN THE MEMORY
Use the ‘STOP/MEM+/AL2’ button on the unit or the ‘M+’ or ‘M-‘ button on the remote control to
select the stored radio station.
Press the ‘STOP/MEM+/AL2’ on the unit or the ‘M+’ button on the remote to go to the next station
in the memory.
Press the ‘M-‘ button on the remote control to go back to the previous station in the memory.
5. Press the ‘PLAY/PAUSE/SYNC’ button to start playing the disc in the programmed order.
6. To stop playing, press the ‘STOP’ button.
7. To cancel the programming list, press the ‘STOP’ button till the ‘STOP’ disappear from the LCD
display or select a different function RADIO, AUX or iPOD/iPHONE.
- 6 -
- 7 -
LISTEN TO iPOD/iPHONE WITH DOCKING CONNECTOR
SLEEP TO MUSIC FUNCTION
1. This function can only operate by remote control.
Warning : Turn off your iPod or iPhone before docking on the unit
2. This function allows you to listen to the radio, iPhone/iPod or CD while you fall asleep.
3. Press the ‘SLEEP/SNOOZE’ button on the remote control, the display will show the default sleep
time of 90 minutes. Press the ‘SLEEP/SNOOZE’ button again to select the sleep time with
decrement of 10 minutes.
4. When the correct sleep time is selected, stop pressing the ‘SLEEP/SNOOZE’ button, the unit will go
to the sleep mode in about 5 seconds with SLEEP appear in the display.
5. Now you can enjoy listening to the selected music for the pre-set period of sleep time.
6. After this pre-set time has elapsed, the unit will switch off automatically.
1. Press the ‘POWER/AL OFF’ button to turn on the unit.
2. Press the ‘FUNC/CL.ADJ’ button to select the iPod mode.
3. Turn the ADJUSTABLE DOCK DIAL to the depth that fit your iPod/iPhone best.
4. Connect the iPod or iPhone to the docking connector, the iPod or iPhone will start playing.
5. Press the ‘VOL+’ or ‘VOL-‘ button to your desired listening level.
6. During playing or in pause mode, press the ‘SKIP+/TUNE+’ button to go to the next track.
7. During playing, press the ‘SKIP-/TUNE-‘ button once to go back to the beginning of the track.
Press the ‘SKIP-/TUNE-‘ button twice to go back to the previous track.
8. In pause mode, press the ‘SKIP-/TUNE-‘ button once to go back to the previous track.
9. Press the ‘PLAY/PAUSE/SYNC’ button to temporarily pause playing. To resume, press the
‘PLAY/PAUSE/SYNC’ button again.
REMOTE CONTROL OPERATION
Take off the plastic sheet located at the battery compartment tray to activate the remote control.
Point the remote control at the remote sensor on the main unit and press the function button to activate
the function.
Operates the IPod/iPhone with the Remote Control
MENU Button – Use this button to go to the Menu Page of the iPod or iPhone.
UP Button – Use this button to scroll up the selection in the Menu.
DN Button – Use this button to scroll down the selection in the Menu.
ENTER Button – Use this button to confirm the selection.
PLAY/PAUSE Button – Use this button to pause playing or resume playing.
STOP Button – Use this button to stop playing.
SKIP-/TUNE- Button – Use this button to go back to the beginning of the track or to the previous
track.
SKIP+/TUNE+ Button – Use this button to go to the next track.
Warning : Please make sure that your iPod or iPhone is properly docked into the unit. Failure to
do so may damage your iPod.
Charging your iPod
While your iPod or iPhone is docked in the unit and the unit is connected to AC power, your iPod
or iPhone will recharge until your iPod or iPhone is fully charged.
1.
2.
3.
4.
5.
6.
7.
8.
9.
POWER/AL.OFF Button
MENU Button
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
AL2 Button
PROGRAM Button
P-MODE/MONO Button
SLEEP/SNOOZE Button
MUTE Button
AUX-IN CONNECTION
PLAY/PAUSE/SYNC Button
STOP Button
1. Press the ‘POWER/AL OFF’ button to turn on the unit.
2. Press the ‘FUNC/CL.ADJ.’ button to select the AUX mode.
3. Insert one side of the audio cable into the Line-Out or Phone Jack on your MP3 Player or
audio device and the other side into the AUX-IN jack of the unit.
4. Turn on your MP3 player or audio device and follow its playback instructions.
ENTER Button
SKIP+/TUNE+ Button
SKIP-/TUNE- Button
FUNC./CL.ADJ Button
UP Button
VOLUME - Button
VOLUME + Button
MEMORY - Button
MEMORY + Button
MEM Button
MUTE FUNCTION
10. DOWN Button
11. AL1 Button
This function can only operate by remote control.
Press the MUTE button on the remote control to mute the unit, press the MUTE button again to
cancel the function.
- 9 -
- 8 -
CARE AND MAINTENANCE
Always turn off the unit after use.
Keep the unit away from magnetic objects, water or heat sources.
Use a clean soft cloth moistened with lukewarm water to clean the cabinet. Never use
chemical cleaners that could damage the finish of the unit.
Never touch the CD pickup and lens. If fingerprints get on the pickup lens, clean it gently with
a commercial lens cleaner.
Disconnect the unit from any power sources before cleaning.
To remove a disc from its storage case, press down on the centre of the case and lift the disc
out, holding it carefully by the edges.
Fingerprints and dust should be carefully wiped off the disc’s recorded surface with a soft
cloth. Unlike conventional records, compact discs have no grooves to collect dust and
microscopic debris so gently wiping with a soft cloth should remove most particles. Wipe in a
straight line from the inside to the outside of the disc. Small dust particles and light stains will
have absolutely no effect on reproduction quality.
Never use chemicals such as record sprays, anti-static sprays, benzene or thinners to clean
compact discs. These chemicals can irreparably damage the disc’s surface.
Discs should be returned to their cases after use. This avoids serious scratches that could
cause the Laser pickup to skip.
Do not expose discs to direct sunlight, high humidity, or high temperatures for extended
periods. Long exposure to high temperatures can warp the disc.
Do not stick paper or write anything with a ballpoint pen on the label side of the disc.
SPECIFICATIONS
Frequency Range:
FM 88 – 108 MHz
Power Supply:
AC 100V to 240V ~ 50/60Hz
DC Adaptor : 7.5V
2 pcs. UM-4 ‘AAA’ size
1 pc. CR-2025
1.5A
Back-Up Battery :
Remote Control Battery :
Specifications are subject to change without further notice.
- 10 -
|