FirePlace Assembly
Instructions
®
®
DANGER
Please read the following warnings carefully before using your FirePlace. Failure to follow these
warnings may result in serious bodily injury or death, or in a fire causing damage to property.
WARNINGS
Ⅵ Fill the Weber FirePlace bottom with
approximately two pounds of sand before
use. This helps to insulate the bottom of
the FirePlace.
Ⅵ The Weber FirePlace is designed solely for
outdoor use. Indoor use can be lethal.
Ⅵ Use only on noncombustible surfaces,
such as brick, flagstone, concrete, etc.
Do not use on a wooden deck.
Ⅵ Always extinguish fire with the lid. Do not
douse with water; this will fracture the
porcelain finish. Wood fires take a long
time to extinguish. The Weber FirePlace
and the ashes inside may remain hot for
some time. Leave the lid closed until the
Weber FirePlace is cold.
Ⅵ Keep away from flammable materials,
buildings and vehicles when in use.
Ⅵ Exercise the same care that you would
with an open campfire.
Ⅵ Your Weber FirePlace is not to be used by
children.
Ⅵ Do not store the Weber FirePlace with
Ⅵ Keep away from flammable fluids such as
gasoline, charcoal lighter fluid and
alcohol, etc.
combustible materials or ashes inside.
Ⅵ Keep children and pets away from the
®
®
FirePlace when in use.
Ⅵ Never wear loose-fitting or flammable
clothing (such as nylon) when in use.
Ⅵ Do not overload. Before starting the fire
make sure the lid is capable of closing.
Overloading can be dangerous if the lid
cannot extinguish the fire.
Ⅵ Do not use soft woods, like pine or cedar.
Soft woods may "pop" and throw sparks.
Ⅵ Do not burn leaves, paper, plywood or
trash in the Weber FirePlace.
Ⅵ Do not use volatile fluids, such as
gasoline, charcoal lighter fluid or alcohol,
to light or relight fires.
Ⅵ Use only sturdy, long-handled fireplace
equipment, when adding or moving logs.
Ⅵ Do not attempt to move the FirePlace when
in use or hot.
Ⅵ Use barbecue mitts when handling,
because surfaces will be hot when in use.
39935 10/93
Step 3
Step 5
Install Wood Handles
Install Heat Deflector and Fourth Leg
You will need: lid assembly, two top wood handles, two
bottom wood handles, two wood screws and a Phillips
screwdriver.
You will need: heat deflector, bottom assembly, one leg,
two machine screws, four large fiber washers, three steel
washers, two hex nuts, a regular screwdriver and wrench.
Install handles as shown in Figure 2.
Insert the heat deflector between the three legs and
position it so it rests on all the leg tabs, as shown in Figure
4.
Now install the fourth leg using the procedure shown in
Figure 3, and making sure the heat deflector rests on all
leg tabs.
Wood screw
®
®
Top wood handle
Bottom wood handle
Heat deflector
Figure 2
Figure 4
Step 4
Install Three Legs
Leg tab
You will need: three legs, bottom, six machine screws,
twelve large fiber washers, nine steel washers, six hex nuts,
a regular screwdriver and wrench.
Install only three legs as shown in Figure 3. Note that the
machine screws are not installed in the same direction.
CAUTION: Do not overtighten; you may crack the
porcelain finish.
Hex nut
Steel washer
Machine screw
Steel washer
Large fiber
washer
Large fiber
washer
Machine screw
Steel washer
Hex nut
Figure 3
Step 8
Step 6
Final Assembly
Assemble Upper Support Ring
You will need: bottom assembly, ring assembly, lid assembly.
You will need: four uprights, upper support ring, four
machine screws, four hex nuts.
Place the ring assembly inside the FirePlace bottom with the
lower support ring down. Figure 7.
Assemble uprights as shown in Figure 5.
Place the FirePlace lid on the upper support ring. It should
rest on the upright tabs.
Machine screw
Hex nut
Figure 5
Step 7
Assemble Lower Support Ring
You will need: lower support ring, upright assembly, eight
machine screws, eight hex nuts, a screwdriver and wrench.
Assemble lower support ring as shown in Figure 6.
Upper ring
assembly from
Step 5
Figure 7
Lower
support ring
Hex nut
Machine screw
Figure 6
|