Congratulations on your purchase
of this VTech product
NEED HELP?
Our representatives are here
to help you with any questions
concerning the operation of this
product, available accessories,
or any other related issues.
Call Toll Free:
1-800-595-9511
In Canada, Call:
1-800-267-7377
or visit our website at
Important Safety Instructions
F. If the product exhibits a distinct change in performance.
13. Avoid using a telephone (other than cordless) during an electrical storm. There
is a remote risk of electric shock from lightning.
14. Do not use the telephone to report a gas leak in the vicinity of the leak.
15. Only put the handset of your telephone next to your ear when it is in normal talk.
3
Before You Begin
Enhanced 2.4GHz Technology - Your t 2453 operates on a dual band
transmission that combines the best of 2.4GHz and 900MHz technologies,
providing enhanced performance over standard cordless telephones.
About Caller Identification (Caller ID)
Your t 2453 has a caller ID(CID) with call waiting feature that works with
service from your local phone service provider. caller ID with call waiting lets you
see who’s calling before you answer the phone, even when you’re on another call.
You may need to change your phone service to use this feature. Contact your
phone service provider if:
•
You have both caller ID and call waiting, but as separate services
(you may need combined service)
•
•
You have only caller ID service, or only caller waiting service.
You don’t subscribe to any caller ID or call waiting services.
You can use this product with regular caller ID service, and you can use this
product’s other features without subscribing to either caller ID or combined
caller ID with call waiting service.
There are fees for caller ID services, and they may not be available in all areas.
This product can provide information only if both you and the caller are in areas
offering caller ID service, and if both telephone companies use compatible
equipment.
4
Before You Begin
Parts Check List:
5. Battery
6. Belt Clip
7. User’s Manual
1. Base Unit
2. Handset
3. AC Power Adaptor
4. Telephone Line Cord
To purchase replacement batteries, visit us on the web at
9511. In Canada, call VTech Telecommunications Canada Ltd. at 1-800-267-
7377.
5
Installation
Before You Install
1. Choose a location for the base near an electrical outlet and a
telephone jack. This phone requires a modular telephone jack and a stan-
dard electrical outlet (110v AC) not controlled by a wall switch.
2. Install the handset battery. Use only the provided VTech battery, or
equivalent.
a). Align the two holes in the plug with the socket pins, then snap the plug into
place.
b). Place the battery in the compartment with the wires in the lower right
corner. Angle the top of the battery under the top claws first, then snap the
bottom of the pack in. Place the wires under the guide, located below the
battery.
c). Replace cover by sliding it up into place.
d). If the battery is not already charged, please the handset in its base when
not in use to ensure maximum daily performance.
a
c
6
Installation
3. Attach belt clip to the cordless handset (optional).
To attach
To remove
Table/Desk Installation
Standard
electrical outlet
Modular
telephone
jack
After charging the battery for at
least 12 hours, connect the tele-
phone line cord.
Connect the power cord.
NOTE: Install the base unit away from
electronic equipment such as personal
computers, television sets or micro-
wave ovens. Avoid excessive heat,
cold, dust or moisture.
7
Installation
4. Charge the Handset Battery
Place the handset in the base. Charge the battery for at least 15 hours the
first time.
NOTE: If the phone will not be used for a long period of time, remove the battery
to prevent possible leakage.
5. Check for Dial Tone
After the batteries are charged, pick up the handset and press PHONE; you
should hear a dial tone.
6. Set the Dial Mode
If you have touch tone service, the phone is ready to use as soon as the
battery is charged. If you have pulse (rotary) service, you’ll need to change the
dial mode.
•
•
Press PROG.
Press or
until the screen displays DIAL MODE: and the
currently selected mode.
•
•
•
Press SELECT. The current setting blinks.
Press to select TONE or PULSE.
Press SELECT to save.
7. Set Time and Date
If you subscribe to CID service, the date and time will be set automatically with
the first incoming call. If you do not have CID service, you can set the date and
time manually:
•
•
•
•
•
•
Press PROG/CHAN, then press
Press SELECT.
or
until DATE/TIME is displayed.
The month is flashing. Press
or
or
or
or
until the screen displays the correct
month. Press SELECT.
The day is flashing. Press
day. Press SELECT.
until the screen displays the correct
until the screen displays the correct
until the screen displays the correct
The hour is flashing. Press
hour. Press SELECT.
The minute is flashing. Press
minute. Press SELECT.
AM or PM is flashing. Press
PM. Press SELECT.
or
to choose between AM or
8. Set Language Mode
•
•
•
Press PROG/CHAN, then press
Press SELECT.
The current setting blinks. Press
correct language (English, Espanol or French).
or
or
until LANGUAGE is displayed.
until the screen displays the
Press SELECT to save your selection.
8
Installation
Your t 2453 base unit is designed to mount on a standard telephone wall plate.
Wall mounting is optional.
1
2
3
1. Open the hinged wall mount bracket on the underside of the base, then
swivel it down and lock it into place as shown in the diagram above.
2. Run the power and telephone cords through the slot, then connect them to
the jacks located on the underside of the base.
3. Plug the AC adapter into an electrical outlet. If the battery has not been
previously charged, place the handset in the base, and allow it to charge for
15 hours (or overnight). Connect the telephone line cord to the wall jack.
4. Mount the base on the wall. Position the base unit so the mounting studs will
fit into the holes on the wall mount bracket. Slide the base unit down on the
mounting studs until it locks into place.
9
Telephone Operation
Handset Operation
Answer a Call
Press any key
except OFF.
Hold
Handset Volume
Adjust the volume
while on a call. A
double beep will
sound when you
reach the maximum or
minimum setting.
Press to put a call
on hold. Press again
to release hold.
-OR-
Use the extension
phone to pick up the
call.
Select
Use SELECT in con-
junction with PROG
during handset pro-
gramming.
Make a Call
Press PHONE, then dial
the number.
-OR-
End a Call
Press OFF.
-OR-
Place handset
in it base.
Dial the number (use
to backspace and make
corrections), then press
PHONE to call.
Exit
Programming
Cancel a Page
Flash/Call Waiting
Access special
telephone company
subscriber services.
During a call, press to
receive an incoming
call, if call waiting is
activated.
Redial
Press PHONE, then press RE-
DIAL/PAUSE to call the last
number dialed (up to 32 dig-
its).
-OR-
Press REDIAL/PAUSE, then
press PHONE to call the last
number dialed.
Channel
Switch to a clear channel
while on a call.
Press REDIAL/PAUSE twice to
delete the last number dialed.
Delete
While handset is in idle mode,
press and hold to delete all
records in the call log.
When viewing the call log,
press to delete the current
record displayed.
Program
Pause
Enter programming
mode with handset
idle (on hook).
Press REDIAL/PAUSE to inset
a pause when entering num-
bers.
10
Telephone Operation
In Use/Charging
• Flashes in unison with inbound calls.
• Flashes slowly when the handset is in use.
• Flashes rapidly when a call is on hold.
• Glows steadily when the handset is charging.
Page
Press to page the handset for up to
60 seconds. Press again, or press OFF
on handset, or place handset in base
to cancel the page.
11
Telephone Operation
Handset Ringer Style/Battery Save
You can select from four different handset ringer styles, or turn the ringer off and
extend the battery life.
1. With the handset in OFF mode, press PROG/CHAN.
2. Press
until the screen displays RINGER:.
3. Press SELECT. The current setting blinks, and you will hear a sample of the ring.
4. Press or to select RINGER: 1, 2, 3, 4 or OFF. You will hear a sample of
each ring tone.
5. Press SELECT to choose the displayed ringer setting.
Temporary Tone Dialing
If you have pulse (rotary) service, you can change from dial pulse to touch tone
dialing during a call by pressing TONE. This is useful if you need to send touch
*
tone signals for access to telephone banking or long distance services.
1. Dial the number.
2. Press TONE. Buttons pressed after this send touch tone signals.
*
3. After you hang up, the phone automatically returns to pulse service.
Headset Jack
You can use this telephone handsfree when you install any VTech 2.5 mm
headset, purchased separately.
Plug the headset into the jack located
on the right side of the handset
(under the small rubber flap).
Do not force the connection,
but make sure the plug
fits securely.
12
Telephone Operation
Operating Range
This cordless telephone operates within the maximum power allowed by the
Federal Communications Commission (FCC). Even so, this handset and base
can communicate over only a certain distance — which can vary with the
locations of the base and handset, the weather, and the construction of your
home or office.
If you receive a call while you are out of range, the handset might not ring or if
it does ring, the call might not connect when you press PHONE. Move closer to
the base, then press PHONE to answer the call.
If you move out of range during a phone conversation, you might hear noise or
interference. To improve reception, move closer to the base.
If you move out of range without pressing OFF, your phone will be left off the
hook. To hang up properly, walk back into range, periodically pressing OFF.
Display Screen Messages
Screen Displays:
When:
Screen Displays: When
There is a call coming in.
** RINGING **
The handset is waiting for dial tone.
CONNECTING...
PHONE ON
The handset is in use.
The base is paging the handset.
** PAGING **
HOLD
There is a call on hold.
BATTERY LOW
SCANNING...
The battery needs to be recharged.
The handset is changing to another of the 30
channels available.
Displays and a sad tone sounds when the base
power is off and PHONE is pressed.
NO CONNECT
RINGER OFF
The handset ringer is turned off.
13
Telephone Memory
You can store up to nine numbers with names (up to 15 characters and 24 digits in each
location) you dial frequently into the speed dial memory locations you assign (1 through
9) in each handset. You can also store telephone numbers with names alphabetically in
the directory. See Telephone Directory for instructions.
NOTES:
•
The entries you stored in speed dial memory will be marked with 01 through 09 in the
telephone directory.
•
Press OFF at any time to exit memory dial mode.
Store a Number/Name in Memory:
1. Press PROG on the handset.
2. Press
or
until the screen displays SPEED DIAL.
3. Press SEL. The screen displays ENTER 1-9.
NOTE: When memory is full the screen displays MEMORY FULL, an error tone sounds,
and you cannot store a new number until you delete a record in speed dial memory or
telephone directory.
4. Press the key (1 through 9) for the memory location where you want to store this
entry.If the selected location is empty, the screen displays ENTER NAME.
NOTE: If the location is not empty, your new entry will be stored in place of the old and the
first entry will be deleted. Take caution to not save over entries you do not wish to delete
from memory.
5. Using the chart below, enter up to 15 characters for the name you’re storing with the
number. Use
space.
to backspace and make corrections; use
to advance and add a
Presses
Dial Key
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
0
*
#
1
A
D
G
J
B
E
H
K
N
Q
U
X
C
F
I
2
3
4
5
6
S
8
Z
L
M
P
T
O
R
V
Y
7
9
W
0
*
&
’
,
-
.
#
14
Speed Dialing
6. When you finish entering the name, press SELECT or PROG. The screen displays
ENTER NUMBER.
7. Enter the telephone number. Use
to backspace and make corrections. Press
REDIAL/PAUSE to store a pause in the dialing sequence.
-OR-
Press REDIAL/PAUSE to display the last number dialed from this phone.
8. Press SELECT or PROG to store your entry. The screen displays DISTINCT
RING? and the current setting.
9. Press
or
to change the setting. Choose Y (for yes) if you wish the phone to alert
you to calls from this number by changing to a distinctive ringing pattern after the
first ring. Choose N for a normal ringing pattern.
10. Press SELECT or PROG to confirm your selection. If you chose Y, a D will be
displayed with the directory entry.
Edit a Number/Name Stored in Memory
1. Press and hold the memory location key (1 through 9) of the entry you wish to edit.
2. When the screen displays the entry you want to edit, press SELECT. Then press
or
until EDIT flashes.
SPEED EDIT ERASE
8005959511
01
3. Press SELECT. The screen displays the name and number. The cursor appears at
the end of the name. Use and the dial pad keys to edit the name. Press
SELECT to move on to edit the number. Use to backspace and make corrections.
,
Press SELECT to move to edit the distinctive ring setting.
4. Press SELECT to save.
Delete a Number/Name Stored in Memory
1. Press and hold the memory location key (1 through 9) of the entry you wish to delete.
2. When the screen displays the entry you want to delete, press SELECT. Then press
or
until ERASE flashes.
SPEED EDIT ERASE
8005959511
01
3. Press SELECT. The screen displays ERASE NO YES and the number.
4. Press or until YES flashes.
5. Press SELECT. You’ll hear a confirmation beep.
Dial a Memory Number
1. Press and hold the memory location key (1 through 9) of the entry you wish to dial.
2. Press PHONE to dial the displayed memory number.
15
Speed Dialing
Reassign Locations in Memory
1. Press and hold the memory location key (1 through 9) of the entry you wish to
reassign.
2. When the screen displays the entry you want to reassign, press SELECT.
Then press
until SPEED flashes.
SPEED EDIT ERASE
8005959511
01
3. Press SELECT. The screen displays ENTER 1-9.
4. Press the keys (1 through 9) to reassign this entry into another memory location.
You’ll hear a confirmation beep.
16
Telephone Directory
Your t 2453 can store 50 (including the nine speed dial entries) numbers with names (up
to 15 characters for the name and 24 digits for the number) in each handset.
NOTE: Press OFF at any time to exit directory.
Store a Number/Name in the Directory
1. Press PROG. The screen displays DIRECTORY.
2. Press SELECT. The screen displays ENTER NAME.
3. Using the chart below, enter up to 15 characters for the name you’re storing with
the number. Use to backspace and make corrections; use to advance and
add a space.
Presses
1 2 3 4 5 6
Dial Key
Dial Key
1
2 3 4 5 6
1:
2:
3:
4:
5:
6:
7:
8:
9:
0:
*:
1
A
D
G
J
B
E
H
K
N
Q
U
X
C
F
I
2
3
4
5
6
S
8
Z
L
M
P
T
W
0
O
R
V
Y
7
9
*
#:
&
’
,
-
.
#
4. When you finish entering the name, press SELECT or PROG. The screen displays
ENTER NUMBER.
5. Enter the telephone number. Use to backspace and make corrections. Press
REDIAL/PAUSE to store a pause in the dialing sequence.
-OR-
Press REDIAL/PAUSE to display the last number dialed fromthisphone.
6. Press SELECT or PROG. The screen displays DISTINCT RING? and the current
setting.
7. Press or to change the setting. Choose Y (for yes) if you wish the phone to
alert you to calls from this number by changing to a distinctive ringing pattern after
the first ring. Choose N for a normal ringing pattern.
17
Telephone Directory
8. Press SELECT or PROG to confirm your selection. If you chose Y, a Dwill be
displayed with the directory entry.
NOTE: When memory is full the screen displays MEMORY FULL, an error tone sounds,
and you will not be able to store a new number until you delete a stored number.
Edit a Number/Name Stored in the Directory
1. Press (DIR). The screen displays DIRECTORY.
2. Press or to scroll alphabetically through the entries stored in the directory.
-OR-
Press the dial pad key for the first letter of the entry you want to edit.
3. When the screen displays the entry you want to edit, press SELECT. Then press
or until EDIT flashes.
SPEED EDIT ERASE
8005959511
4. Press SELECT. The screen displays the name and number. The cursor ap-
pears at the end of the name. Use
,
and the dial pad keys to edit the
name. Press SELECT to move on to edit the number. Use
to back space
and make corrections. Press SELECT to move on to edit the distinctive ring
setting.
5. Press SELECT to save the edited information.
Delete a Number/Name Stored in the Directory
1. Press (DIR). The screen displays DIRECTORY.
2. Press or to scroll alphabetically through entries in the directory.
-OR-
Press the dial pad key for the first letter of the entry you want to delete.
3. When the screen displays the entry you want to delete, press SELECT. Then press
or until ERASE flashes.
SPEED EDIT ERASE
8005959511
4. Press SELECT. The screen displays ERASE NO YES and the number. The current
choice flashes.
5. Press or until YES flashes.
6. Press SELECT. You’ll hear a confirmation beep.
Dial a Number from the Directory
1. Press (DIR). The screen displays DIRECTORY.
2. Press or to scroll alphabetically through entries stored in directory.
18
Telephone Directory
-OR-
Press the dial pad key for the first letter of the entry you want to dial.
3. When the number you want to dial is displayed, press PHONE.
Move a Number/Name to the Memory
1. Press (DIR). The screen displays DIRECTORY.
2. Press or to scroll alphabetically through directory.
— OR —
Press the dial pad key for the first letter of the entry you want to move.
3. When the screen displays the entry you want to move, press SELECT. Then press
until SPEED flashes.
SPEED EDIT ERASE
8005959511
01
4. Press SELECT. The screen displays ENTER 1-9.
5. Press the key (1 through 9) to move this entry from the normal directory to the speed
dial memory and assign the memory location. You’llhearaconfirmation beep. A memory
location number (01 through 09) will be displayed with this entry.
19
Caller ID Operation
Caller’s name
Party has called
2 or more times
*
VTech
L 800-595-9511
Long distance call
C a l l e r ’ s
telephone
number
AM
NEW
5/01 5:40 28
OLD
PM
Date of call
Position of call
in call history
Time of call
About Call History (Caller ID)
Your t 2453 can store up to 50 calls in its caller ID memory. The most recent call will have
the highest number. When the memory is full, the oldest call will be deleted to make room
for new incoming call information. For each call that comes in, the screen displays the
following information between the first and second rings:
•
•
•
•
Your caller’s name (15 letters are sent by your telephone company).
The caller’s area code and telephone number.
The time and date of the call.
The repeat tag (*) in the upper right corner, indicating the party has called more than
once.
If you answer a call before the information appears on the screen, it will not be in the call
history.
NOTE: Each handset's call log is independent from the other handset. For example, when
you delete one or all call log entries in one handset, they will not be deleted from the other
handset.
Review Call History
1. Press
2. Use
(CID) to view call history.
to scroll through records in call history.
and
NOTE: Press OFF at any time to exit call history.
Delete Records from Call History
Delete a Specific Call:
1. Locate the record you want to delete from call history.
2. Press DELETE. You’ll hear a confirmation beep.
Delete All Calls:
1. With the handset in idle (OFF) mode, press and hold DELETE. The screen displays
ERASE ALL NO YES. The current choice flashes.
2. Press
until YES flashes.
3. Press SELECT. You’ll hear a confirmation beep.
20
Caller ID Operation
Dial a Displayed Number
1. Locate the record in call history that you want to dial.
2. If you wish to change how the number is dialed, press #. The screen displays
alternate dialing sequences available for this call (area code + number; 1 +
area code + number; number only; 1+ number).
3. Press SELECT. Press
until DIAL flashes.
DIAL PROGRAM
8005959511
5/01 5:40PM
OLD28
4. Press SELECT again. The number is automatically dialed.
— OR —
When the number is correctly displayed for dialing, press PHONE.
Store a Call History Record in the Directory
1. Locate the record in the call history you want to store in the directory.
2. If you wish to change how the number is stored, press #. The screen displays
alternate dialing sequences available for this call (area code + number; 1 +
area code + number; number only; 1+ number).
3. Press SELECT, then press
until PROGRAM flashes.
DIAL PROGRAM
8005959511
5/01 5:40PM
OLD28
4. Press SELECT three times. The screen displays:
DISTINCT RING? N
8005959511
5. Press
or
to select Y or N for distinctive ringer.
6. Press SELECT. You’ll hear a confirmation beep. If you choose Y in step 5 a
D will be displayed with the directory entry.
21
Caller ID Operation
Display Screen Messages
Screen Displays: When:
PRIVATE
The other party is blocking name and/or number
information.
UNKNOWN
Your phone company is unable to receive
information about this caller’s name and/or number.
* (after the name)
This caller has called you more than once.
22
Answering System Operation At The Base
Audible Indicators
Your t 2453 telephone system gives you voice prompts for feature opera-
tions and voice confirmations when you press a button or complete an op-
eration.
NOTE:
The time will be set automatically with incoming caller ID data. If you do not
subscribe to caller ID service (fee required), or simply wish to set the clock
manually:
Setting the clock
1. Make sure the answering system is on.
2. Press TIME/SET. The system announces the clock setting, then announces:
“To Set Day and Time, press TIME/SET.”
3. Press TIME/SET.
4. Press CHANGE until the system announces the correct day, then press
TIME/SET.
5. Press CHANGE until the system announces the correct hour, then
press TIME/SET.
6. Press CHANGE until the system announces the correct minute, then
press TIME/SET. The system announces the current clock setting.
To advance the minutes or years by increments of 10, press and hold CHANGE.
About Mailboxes
This answering system has three voice mailboxes. Callers using a touch tone
phone can select the mailbox in which their messages will be recorded
by pressing 1, 2 or 3. Otherwise, messages will be recorded in Mailbox 1.
About Announcements
•
You can record two different announcements — one for normal answering
and one for when you’ve set the system to play the announcement only.
Use normal answering when you want the system to record callers’
messages. Use Announce Only when you want to give information to
callers without accepting messages.
•
•
•
If you choose not to record an announcement, the system answers with a
pre-recorded announcement.
The normal answering pre-recorded announcement says: “Hello. I’m unable to
answer your call right now. Please leave your name, number and a
message after the tone.” The Announce Only pre-recorded
announcement says: “Hello, I’m unable to answer your call right now. Please
call again. Thank you.”
•
By setting Announce Only to ON or OFF, you decide which announcement your
callers will hear when the system answers a call (the system comes set for
normal answering, with Announce Only turned off). See Set Announce
Only, located in the Feature Summary chart later in this section, to change
your announcement selection.
23
Answering System Operation At The Base
Select a feature
setting
Turn Answering
System on or off
Enter Answering
System feature
setup and choose
a feature to set.....
Review/change
clock setting;
confirm feature
settings .
Record outgoing
announcements,
and memos.
Record Your Announcement
NOTE: If you have assigned different mailboxes to different people, be sure to
tell callers in your announcement to press 1 ,2 , or 3 to leave a message in the
appropriate mailbox. For example: “Thank you for calling. To leave a message
for Bob, press 1 now. To leave a message for Sue, press 2 now. To leave a
message for Elmo, press 3 now. Or, wait for the beep, and leave your message.”
1. Press MENU until you hear “Record Outgoing Message.”
2. Press REC/MEMO. After you hear “Now recording” followed by a beep, speak
toward the base to record an announcement up to 90 seconds long.
3. Press any MAILBOX button to stop recording. The system plays back your
recorded message.
To review your announcement at any time:
1. Press MENU until you hear “Record Outgoing Message.”
2. Press any MAILBOX button.
To delete your announcement:
Press DELETE during announcement playback. The system will use the
pre-recorded announcement until you record a new one.
24
Answering System Operation At The Base
Setting Up Your Answering System
You can set up one feature at a time, or you can set up a feature and then move
on to set up another feature.
1. Make sure the answering system is on.
2. Press MENU until the system announces the feature you want to set. Refer
to the Feature Summary below for a description of the features and your choices.
3. Press SELECT until the system announces the desired setting.
4. Press TIME/SET to confirm your selection.
5. Press MENU to move on to the next feature, or press a MAILBOX
button to exit Feature Setup.
Feature Summary
Default settings indicated by *
.
System announces: Description/directions:
“Set Security Code”
Use SELECT to choose the remote access code
you will use to access features and functions of the
answering system from a touch tone phone. You can
select any 2-digit code, from 40 to 99.
*
50
NOTE: To advance the remote access code by
10, press and hold SELECT.
“Set Audible Message Alert ” When Message Alert is turned on, the base beeps
*
Off
On
once every 10 seconds when new messages
have been received.
“Set Announce Only”
Off
When you turn Announce Only On, callers hear
your announcement, but cannot leave a message
*
On
“Set Base Ringer”
On
Turn the base ringer on or off.
*
Off
“Set Number of Rings”
2
Choose how many times the phone will ring
before the system answers a call.
With Toll Saver active, the system answers after two
rings when you have new messages and after
four rings when you have no new messages.
4 *
6
Toll Saver
NOTE: You can exit Feature Setup at any time by pressing a MAILBOX button.
25
Answering System Operation At The Base
Listen to, Save & Delete Messages
The system automatically saves your messages until you delete them, and can
store approximately 15 minutes of messages, memos, and announcements
(up to a maximum of 99 messages).Your caller can leave a message of up to 4
minutes in length.
A MAILBOX key will flash to alert you to new, unplayed messages. If all messages
in a mailbox have been reviewed, the key will glow steadily. A mailbox containing
both old and new messages will play only the new messages first. After all new
messages are played, press the MAILBOX key again to hear all messages.
Before playing a message, the system announces the day and time it was
received. While the message plays, the Message Window displays the num-
ber of the message. After playing the last message in a mailbox, the system
announces “End of messages.” If the system has less than five minutes of
recording time left, it announces remaining time.
Note: When listening to your messages, if after the date and time stamp
your system announces “power failure” it is alerting you that your date and
time stamp is no longer accurate due to a power outage. you‘ll need to
reset the clock.
Message Window
Press to skip to the next
message; hold to speed up
playback.
Play Messages
Press to play messages
in a mailbox. Press again
to stop playback.
• Press DELETE • You cannot
Delete Messages
Press to
repeat a
message;
hold to
slow down
playback.
delete a
then press a
MAILBOX
button to delete
all old
• To delete a
message, press
DELETE while
the message
is playing.
message
until it’s been
reviewed;
deleted
messages
messages cannot
be recovered.
in that mailbox.
26
Answering System Operation At The Base
Call Screening/Intercept
1. Make sure the answering system is on, and set the message playback vol-
ume control above level 1 so you can hear the callers’ message.
2. If you decide to take the call, press PHONE on the handset.
3. If you pick up an extension phone during the announcement and the
announcement does not stop right away, press and release the telephone
switchhook.
Record a Memo
You can record a memo up to four minutes long, which is stored as an incom-
ing message.
1. Press and release REC/MEMO.
2. Press a MAILBOX button to select a mailbox for the memo. After the
beep, speak toward the microphone. The message window displays the
length of your memo.
3. To stop recording, press the MAILBOX button again.
Message Window Display
Window Display: when:
0
No messages in any mailbox
1 - 99
Total number of messages in all mailboxes, or
message number during message playback.
0 - 99 F
1to 99 (Counting)
99(flashing)
Memory is full, or total number of messages is 99
Duration of memo recording.
Length of recording is more than 99 seconds.
1- 8(on steady for
Indicates volume level selected when VOL-
one second)
or VOL+ is pressed.
40- 99
Current Remote Access Code while setting.
Announce Only mode.
A
Onor OFF(steady for Displayed when any setting is changed from on or
one second)
off.
CL
Clock needs to be set.
--
System is answering a call or is in remote operation.
System is in programming mode or initializing.
-- (flashing)
27
Answering System - Remote Access
Connect with the Answering System
You can access many features of this system remotely from a touch tone phone.
1. Dial your telephone number.
2. When the system answers, enter your Remote Access Code (preset to 50).
The system beeps once and then announces the number of new messages.
3. Enter a remote command (see Remote Access Commands).
4. Press * 0 to exit remote operation.
Voice Menu
The system has voice prompts to help you with remote operation. Press
* 5 to hear the menu while remotely connected to the answering system.
Remote Access Commands
Function:
Command:
Play messages in
a mailbox
Press # , then the appropriate mailbox
number (1,2, or3). The system plays
new messages. If there are no new messages,
the system plays old messages.
Repeat a message
Skip a message
Press #4 while message is playing; press
#4#4 to back up previous message.
Press #6 while message is playing;
each press advances up another message.
Stop
Press #5 .
Save messages
Delete message
Review announcement
Hang up.
Press #9 while message is playing.
Press #7; system plays announcement,
then beeps.
Record announcement
Press *7; after beep, record announcement,
press #5 to stop. System plays back
announcement.
28
Answering System - Remote Access
Remote Access Commands (continued)
Function:
Command:
Function: Command:
Record memo
Press *8 , then mailbox number where
you want memo recorded; speak after
beep; press #5 when finished.
End remote access call
Turn system off
Press *0 .
Press #0; the system announces,
“Answering machine off.” Press # 0
again to turn the system back on.
Turn system on
When system is off, it answers after 10
rings and announces, “Please enter your
security code.” Enter your remote access
code.
NOTE: If no key is pressed within 10 seconds of entering remote access, the
voice menu will be announced. After the voice menu announcement, if no key is
pressed within 20 seconds, the remote access call will automatically end.
29
Batteries
Battery Care and Maintenance
•
A fully charged battery provides an average talk time of about six hours.
•
The battery needs charging when:
—
—
—
A new battery is installed in the handset.
The phone beeps twice every five seconds.
The screen displays BATTERY LOW and the low battery icon.
•
•
•
Place the handset in the base so the CHARGING light turns on.The battery
is typically fully charged in 15 hours.
You can keep the battery fully charged by returning the handset to the base
after each use.
If you repeatedly get a low battery indicator, even after charging overnight,
the battery should be replaced.
CAUTION: To reduce the risk of fire or injury to persons or damage
to the telephone, read and follow these instructions carefully:
Charge the battery provided with or identified for use with this
product only in accordance with the instructions and
limitations specified in the User’s Manual.
Replacing the Handset Battery
1. Remove the battery compartment cover on the handset by pressing on the
indentation and sliding the cover downward.
2. Lift out the old Battery and disconnect.
3. Align the two holes in the new battery’s plug with the socket pins, and snap
the plug into place. Snap the battery in the compartment, as described in
Installation, on page 6.
4. Replace the cover by sliding it up into place.
5. The new battery must be charged before using the phone. Place the hand-
set in the base and allow it to charge for at least 15 hours the first charge.
The telephone might operate before that, but for best performance, let the
battery charge fully.
1
3
4
30
In Case Of Difficulty
If you have difficulty operating your phone, the suggestions below should solve the prob-
lem. If you still have difficulty after trying these suggestions, call VTech Communica- tions
at 1-800-595-9511. In Canada, call VTech Telecommunications Canada Ltd. at 1-800-
267-7377.
The phone doesn't work at all
•
•
Make sure the power cord is plugged in.
Make sure the telephone line cord is plugged firmly into the base unit and the
telephone wall jack.
•
Make sure the batteries are properly charged. If you get a LOW BATTERY message
or indication, the batteries need charging.
No dial tone
•
•
First try all the suggestions above.
If you still don't hear a dial tone, disconnect the base unit from the telephone jack
and connect a different phone. If there is no dial tone on that phone either, the
problem is in your wiring or local service. Contact your local telephone company.
You get noise, static, or a weak signal even when you're near the base unit
•
Household appliances plugged into the same circuit as the base unit can sometimes
cause interference. Try moving the appliance or the base unit to another outlet.
You get noise, static, or a weak signal when you're away from the base
unit
•
You may be out of range. Either move closer to the base, or relocate the base
unit.
•
The layout of your home may be limiting the range. Try moving the base unit to
another position.
The handset does not ring when you receive a call
•
Make sure you have the ringer activated. Refer to the section(s) on ringer
selection in this User’s Manual.
•
Make sure the telephone line cord is plugged firmly into the base unit and the
telephone jack. Make sure the power cord is plugged in.
You may be too far from the base unit.
You may have too many extension phones on your telephone line to allow all of
them to ring. Try unplugging some of the other phones.
The layout of your home or office might be limiting the operating range. Try moving the
base to another location, preferably on an upper floor.
•
•
•
You hear other calls while using your phone
•
Disconnect your base unit from the telephone jack, and plug in a regular telephone.
If you still hear other calls, the problem is probably in your wiring or local service.
Call your local telephone company.
You hear noise in the handset, and none of the keys or buttons work
•
Make sure the power cord is plugged in.
31
In Case Of Difficulty
Common cure for electronic equipment
If the unit does not seem to be responding normally, then try putting the handset
in its base. If it does not seem to respond, do the following (in the order listed):
1. Disconnect the power to the base.
2. Disconnect the handset battery, and spare battery, if applicable.
3. Wait a few minutes.
4. Connect power to the base.
5. Re-install the battery(ies).
6. Wait for the handset to re-establish its link with the base. To be safe, allow
up to one minute for this to take place.
Your answering system is not recording messages
•
•
Make sure system is turned ON (the ON/OFF key is illuminated).
Make sure the Announce Only feature is set to OFF.
You cannot hear recorded messages
•
Using the base volume control, raise the volume to a comfortable listening
level.
CL is flashing in the base Message Window Display:
•
You need to set the day and time. Refer to the section(s) on setting day and
time in this user’s manual.
•
Make sure Announce Only feature is set to OFF.
If the system does not respond to commands from a remote touch tone phone:
•
Make sure you are calling from a touch tone phone. When you dial a
number, you should hear tones. If you hear clicks instead, the phone is not
a touch tone telephone.
The answering system may not detect the Remote Access Code while your
announcement is playing. Try waiting until the announcement is over be-
fore entering the code.
•
Make sure you enter your Remote Access Code correctly.
32
Maintenance
Taking care of your telephone
Your cordless telephone contains sophisticated electronic parts, so it must be
treated with care.
Avoid rough treatment
Place the handset down gently. Save the original packing materials to protect
your telephone if you ever need to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not use the handset outdoors
in the rain, or handle it with wet hands. Do not install your base unit near
a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic
equipment.
For your own safety, use caution when using electric appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should retain its luster for
many years. Clean it only with a soft cloth slightly dampened with water or
a mild soap. Do not use excess water or cleaning solvents of any kind.
Remember that electrical appliances can cause serious injury if used when
you are wet or standing in water. If your base unit should fall into water,
DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND
TELEPHONE LINE CORDS FROM THE WALL. Then pull the unit out by the
unplugged cords.
33
Warranty Statement
What does this limited warranty cover?
• The manufacturer of this VTech product, VTech Communications, warrants
to the holder of a valid proof of purchase (“Consumer” or “you”) that the
product and all accessories provided by VTech in the sales package
(“Product”) are free from material defects in material and workmanship,
pursuant to the following terms and conditions, when installed and used
normally and in accordance with operation instructions. This limited warranty
extends only to the Consumer for Products purchased and used in the United
States of America.
What will VTech Communications do if the Product is not free from material
defects in materials and workmanship during the limited warranty period
(“Materially Defective Product”)?
• During the limited warranty period, VTech’s authorized service representative
will repair or replace at VTech’s option, without charge, a Materially
Defective Product. If we repair this product, we may use new or refurbished
replacement parts. If we choose to replace this product, we may replace it
with a new or refurbished product of the same or similar design. VTech will
return repaired or replacement products to you in working condition. VTech
will retain defective parts, modules, or equipment. Repair or replacement
of Product, at VTech’s option, is your exclusive remedy. You should expect
the repair or replacement to take approximately 30 days.
How long is the limited warranty period?
• The limited warranty period for the product extends for ONE(1)YEAR from
the date of purchase if we repair or replace a Materially Defective Product
under the terms of this limited warranty. This limited warranty also applies
to repaired or replacement Products for a period of either (a) 90 days from
the date the repaired or replacement Product is shipped to you or (b) the
time remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover
1. Product that has been subjected to misuse, accident, shipping or other
physical damage, improper installation, abnormal operation or handling,
neglect, inundation, fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by
anyone other than an authorized service representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal
conditions, network reliability or cable or antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTech
electrical accessories; or
34
Warranty Statement
5. Product whose warranty/quality stickers, Product serial numbers plates
or electronic serial numbers have been removed, altered or rendered
illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the
United States, or used for commercial or institutional purposes (including
but not limited to Products used for rental purposes ); or
7. Product returned without valid proof of purchase (see 2 below); or
8. Charges for installation or set up, adjustment of customer controls, and
installation or repair of systems outside the unit.
How do you get warranty service?
..
• To obtain warranty service in the United States of America, call 1-800-595-
9511 for instructions regarding where to return the Product. Before calling
for service, please check the user’s manual. A check of the Product controls
and features may save you a service call.
• Except as provided by applicable law, you assume the risk of loss or damage
during transit and transportation and are responsible for delivery or handling
charges incurred in the transport of Product(s) to the service location. VTech
will return repaired or replaced product under this limited warranty to you,
transportation, delivery or handling charges prepaid. VTech assumes no risk
for damage or loss of the Product in transit.
• If the Product failure is not covered by this limited warranty, or proof of
purchase does not meet the terms of this limited warranty, VTech will notify
you and will request that you authorize the cost of repair prior to any further
repair activity. You must pay for the cost of repair and return shipping costs
for the repair of Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1.Return the entire original package and contents including the Product to the
VTech service location along with a description of the malfunction or difficulty;
2.Include “valid proof of purchase” (sales receipt) identifying the Product
purchased (Product model) and the date of purchase or receipt; and
3.Provide your name, complete and correct mailing address, and telephone
number.
Other Limitations
• This warranty is the complete and exclusive agreement between you and
VTech. It supersedes all other written or oral communications related to this
Product. VTech provides no other warranties for this product. The warranty
exclusively describes all of VTech’s responsibilities regarding the product.
There are no other express warranties. No one is authorized to make
modifications to this limited warranty and you should not rely on any such
modification.
State Law Rights: This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
35
Warranty Statement
Limitations: Implied warranties, including those of fitness for a particular
purpose and merchantability (an unwritten warranty that the product is fit for
ordinary use) are limited to one year from date of purchase. Some states
do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you.
• In no event shall VTech be liable for any indirect, special, incidental,
consequential, or similar damages (including, but not limited to lost profits
or revenue, inability to use the product, or other associated equipment, the
cost of substitute equipment, and claims by third parties) resulting from the
use of this product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion
may not apply to you.
36
FCC, ACTA and IC Regulations
This equipment complies with Parts 15 of the Federal Communications
Commission (FCC) rules for the United States. It also complies with regulations RSS210 and
CS-03 of Industry and Science Canada. Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device.
A label is located on the underside of the base unit containing either the FCC
registration number and Ringer Equivalence Number (REN) or the IC registration
number and Load Number. You must, upon request, provide this information to your
local telephone company.
This equipment is compatible with inductively coupled hearing aids.
Should you experience trouble with this telephone equipment, please visit us on web at
595-9511.InCanada,callVTech Telecommunications Canada Ltd. at 1-800-267-7377.
For repair/warranty information, the telephone company may ask you to disconnect this
equipment from the line network until the problem has been corrected.
FCC Part 15
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
The equipment has been tested and found to comply with part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouragedtotryandcorrecttheinterferenceby
oneormoreofthefollowingmeasures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet or on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC Part 68 and ACTA
If this equipment was approved for connection to the telephone network prior to July 23,
2001, it complies with Part 68 of the Federal Communications Commission (FCC) rules. If the
equipment was approved after that date, it complies with the Part 68 rules and with
Technical Requirements for Connection of Equipment to the Telephone Network
adopted by the Administrative Council for Terminal Attachments (ACTA). We are
required to provide you with the following information.
37
FCC, ACTA and IC Regulations
1.
Product identifier and REN information
The label on the back or bottom of this equipment contains, among other things, an
identifier indicating product approval and the Ringer Equivalence Number (REN).
This information must be provided to your local telephone company upon request.
For equipment approved prior to July 23, 2001, the product identifier is preceded by the
phrase “FCC Reg No.” and the REN is listed separately. For equipment
approved after that date, the product identifier is preceded by “US”and a colon (:),
and the REN is encoded in the product identifier without a decimal point as the
sixth and seventh characters following the colon. For example, the product
identifier US:AAAEQ03T123XYZ would indicate an REN of 0.3.
The REN is used to determine how many devices you may connect to your
telephone line and still have them ring when you are called. In most, but not all areas,
the sum of all RENs should be five (5.0) or less. For more information, please
contact your local telephone company.
2.
Connection and use with the nationwide telephone network
The plug and jack used to connect this equipment to the premises wiring and the
telephone network must comply with the applicable Part 68 rules and technical
requirements adopted by ACTA. A compliant telephone cord and modular plug is
provided with this product. It is designed to be connected to a compatible
modular jack that is also compliant. An RJ11 jack should normally be used for
connecting to a single line and an RJ14 jack for two lines. See Installation
Instructions in the user’s manual. This equipment may not be used with Coin
Telephone Lines or with Party Lines. If you have specially wired alarm dialing
equipment connected to your telephone line, ensure the connection of this
equipment does not disable your alarm equipment. If you have questions about
what will disable alarm equipment, consult your telephone company or a
qualified installer.
3.
4.
Repair instructions
If this equipment is malfunctioning, it must be unplugged from the modular jack until
the problem has been corrected. Repairs to this telephone equipment can only be
made by the manufacturer or its authorized agents. For repair procedures,
follow the instructions outlined under the Limited Warranty.
Rights of the telephone company
If this equipment is causing harm to the telephone network, the telephone company
may temporarily discontinue your telephone service. The telephone company is
required to notify you before interrupting service. If advance notice is not practical,
you will be notified as soon as possible. You will be given the opportunity to correct the
problem and the telephone company is required to inform you of your right to file
a complaint with the FCC. Your telephone company may make changes in
its facilities, equipment, operation, or procedures that could affect the proper
functioning of this product. The telephone company is required to notify you if such
changes are planned.
5.
Hearing aid compatibility
If this product is equipped with a corded or cordless handset, it is hearing aid
compatible.
38
FCC, ACTA and IC Regulations
6.
Programming/testing of emergency numbers
If this product has memory dialing locations, you may choose to store police, fire
department and emergency medical service telephone numbers in these
locations. If you do, please keep three things in mind:
a
We recommend that you also write the telephone number on the directory card,
so that you can still dial the emergency number manually if the memory dialing
feature doesn’t work.
b
c
This feature is provided only as a convenience, and the manufacturer assumes no
responsibility for customer reliance upon the memory feature.
Testing the emergency telephone numbers you have stored is
not recommended. However, if you do make a call to an emergency number:
•
You must remain on the line and briefly explain the reason for the call
before hanging up.
•
Programming/testing of emergency numbers should be performed
during off-peak hours, such as in the early morning or late evening,
when the emergency services tend to be less busy.
IC (Industry Canada)
This telephone is registered for use in Canada.
The term “IC:” before the radio certification number only signifies that Industry
Canada technical specifications were met.
Notice:
This equipment meets the applicable Industry Canada Terminal Equipment Technical
Specifications. This is confirmed by the registration number. The abbreviation, IC, be-
fore the registration number signifies that registration was performed based on a Decla-
ration of Conformity indicating that Industry Canada technical specifications were met. It
does not imply that Industry Canada approved the equipment.
Notice:
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1B. The REN
assigned to each terminal equipment provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The termination on an
interface may consist of any combination ofdevices subject only to the requirement that the
sum of the Ringer Equivalence Numbers of all the devices does not exceed five.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The equipment
mustalsobeinstalledusinganacceptablemethodofconnection.Thecustomershould
be aware that compliance with the above conditions may not prevent degradation of
services in some situations.
RepairstocertifiedequipmentshouldbemadebyanauthorizedCanadianmaintenance
facility designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications company
cause to request the user to disconnect the equipment.
39
FCC, ACTA and IC Regulations
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic water
pipe system, if present, are connected together. This precaution may be
particularly important in rural areas.
Caution:
Users should not attempt to make such connections themselves, but should
contact the appropriate electrical inspection authority, or electrician, as
appropriate.
Your telephone is designed to operate at the maximum power allowed by
the FCC and IC. This means your handset and base unit can communicate
only over a certain distance - which will depend on the location of the base
unit and handset, weather, and the construction and layout of your home or
office.
The RBRCR Seal
R
The RBRC Seal on the nickel-cadmium battery indicates that VTech
Communications, Inc. is voluntarily participating in an industry program
to collect and recycle these batteries at the end of their useful lives,
when taken out of service within the United States and Canada.
R
The RBRC program provides a convenient alternative to placing used
nickel-cadmium batteries into the trash or municipal waste, which may be illegal in
your area.
VTech’s participation in RBRCR makes it easy for you to drop off the spent battery
at local retailers participating in the RBRC R program or at authorized VTech
product service centers. Please call 1-800-8-BATTERYTM for information on Ni-
Cd battery recycling and disposal bans/restrictions in your area. VTech’s
involvement in this program is part of its commitment to protecting our
environment and conserving natural resources.
RBRC R is a registered trademark of Rechargeable Battery Recycling
Corporation.
40
Technical Specifications
FREQUENCY CONTROL
WEIGHT
Crystal controlled
PLL synthesizer
Handset:
Base:
148 grams
344 grams
TRANSMIT FREQUENCY
POWER REQUIREMENTS
Base: 2410.2 - 2418.9 MHz
Handset: 912.75 - 917.10 MHz
Handset:
400mAHNi-Cd
Battery
RECEIVE FREQUENCY
Base:
9V DC @ 300mA
Base: 912.75 - 917.10 MHz
Handset: 2410.2 - 2418.9 MHz
MEMORY
Speed Dial: 9 Memory locations
24 digits per location
CHANNELS
30 Channels
Directory:
CID:
30 Memory locations
24 digits per location
NOMINAL
RANGE
EFFECTIVE
50 Memory locations
Maximum power allowed by FCC
andIC.Actualoperatingrangemay
vary according to environmental
conditions at the time of use.
SPECIFICATIONS ARE TYPICAL
AND MAY CHANGE WITHOUT
NOTICE.
SIZE
handset: 35mm x 55mm x 205mm
base: 148mm x 171mm x 112mm
41
Table Of Contents
Important Safety Instructions..........................................................................2
Before You Begin...............................................................................................................4
About Caller Identification (Caller ID)................................................................4
Parts Check List......................................................................................................4
Getting Started...................................................................................................................6
Installation.......................................................................................................................6
Before You Install....................................................................................................6
Table/Desk Installation.....................................................................................6
Wall Mounting…...................................................................................................9
Basic Operation................................................................................................................10
Telephone Operation...............................................................................................10
Make a Call ........................................................................................................10
Answer a Call .....................................................................................................10
End a Call ...........................................................................................................10
Program/Channel ..............................................................................................10
Redial ..................................................................................................................10
Handset Volume...................................................................................................10
Flash/Call Waiting ................................................................................................10
Hold.....................................................................................................................10
Select..................................................................................................................10
Memory................................................................................................................10
In Use/Charging...................................................................................................11
Page/Handset Locator.........................................................................................11
Handset Ringer Style/Battery Save ..............................................................11
Temporary Tone Dialing .....................................................................................11
Headset Jack ........................................................................................................12
Operating Range..................................................................................................13
Display Screen Messages .................................................................................13
Telephone Memory .................................................................................................14
Store a Number/Name in Memory ....................................................................14
Edit a Number/Name Stored in Memory ..........................................................15
Delete a Number/Name Stored in Memory ......................................................15
Dial a Memory Number........................................................................................16
Telephone Directory..............................................................................................17
Store a Number/Name in the Directory .........................................................17
Edit a Number/Name Stored in the Directory .................................................18
Delete a Number/Name Stored in the Directory ........................................18
Dial a Number from the Directory ....................................................................19
Table Of Contents
Caller ID Operation......................................................................................................20
About Call History(Caller ID)..............................................................................20
Review Call History.............................................................................................20
Delete Records from Call History...................................................................20
Dial a Displayed Number....................................................................................21
Store a Call History Record in the Directory......................... ...................22
Display Screen Messages...............................................................................22
Answering System Operation At The Base................................................................23
Audible Indicators ..........................................................................................23
Setting Day/Time.............................................................................................23
About Mailboxes ..........................................................................................23
About Announcements...................................................................................23
Record Your Announcement ......................................................................24
Setting up Your Answering System................................................................25
Feature Summary..........................................................................................25
Listen to, Save & Delete Messages..............................................................26
Call Screening/Intercept ................................................................................27
Record a Memo ................................................................................................27
Message Window Display .........................................................................27
Answering System- Remote Access.....................................................................28
Connect with the Answering System ..........................................................28
Voice Menu.....................................................................................................28
Remote Access Commands............................................................................29
Batteries.................................................................................................................... 30
Battery Care and Maintenance.................................................................30
Replacing the Handset Battery.............................................................30
Additional Information..............................................................................................31
In Case of Difficulty....................................................................................................31
Maintenance..................................................................................................................33
Warranty Statement..................................................................................................34
FCC, ACTA and IC Regulations.........................................................................37
R
The RBRC Seal.....................................................................................................40
Technical Specifications..............................................................................................41
VTECH TELECOMMUNICATIONS LTD.
A member of THE VTECH GROUP OF COMPANIES.
Distributed in the U.S.A. by VTech Communications, Inc. Beaverton,
Oregon, 97008
Distributed in Canada by VTech Telecommunications Canada Ltd., Richmond,
B.C. V6X 1Z9.
Copyright 2005 for VTECH TELECOMMUNICATIONS LTD.
Printed in China
91-000173-040-000
ISSUED 0
|